
> Workshop Tools
Brake Tools
DA1153
Crankshaft Tools
Engine Front Casing Alignment Tool
DA1160
Defender - 2007 onwards
Land Rover tool part number - 303-682
226 www.britpart.com
Crankshaft Front Seal
Remover/Installer Tool
DA1161
Defender - 2007 onwards
Older type seals - LR029318 & LR045106
Land Rover tool part number - 303-679
Brake Caliper Rebuild Tool Kit
DA1153
Anyone who has ever tried to rebuild a
set of Land-Rover brake calipers will know
that the most difficult part is fitting the dust
seal after the pistons have been fitted.
This extremely awkward task can now
be made much easier with the seal fitting
tools in this kit. The kit is supplied with a
tool to fit 41mm and 44mm pistons and
comes complete with a heavy-duty piston
spreader to allow the seals to be pushed
into place evenly.
DA7460
Heavy-duty piston spreader only.
Dynamic Response System Bleed Bottle
204-591-01
For use with 204-591-02. For professional
use only.
Dynamic Response Control Box
204-591-02
For use with 204-591-02. For professional
use only.
Crankshaft Front Seal
Remover/Installer Tool
JLR-303-1619
Defender - 2007 onwards
Newer type seals - LR077704
Oil Pump Alignment Tool
DA6111
Defender - 2.2 TD4 diesel - 2006 - 2015
Developed to correctly align the engine oil pump in the
sump after an engine rebuild as it is important that the
pump be correctly and accurately aligned to ensure the oil
pump sprocket is not operating with excessive side loads.
Crankshaft Rear Seal
Remover/Installer Tool
DA6114
Range Rover Sport
2005 - 2009 - 4.4 & 4.2 V8 petrol
Range Rover L322
2002 - 2013 - 4.4 & 4.2 V8 petrol
Discovery 3 - 2004 - 2009 - 4.4 V8 petrol
Suitable for use on vehicles with the petrol
AJV8 engine both N/A and supercharged.
Comes complete with punch to assist seal
removal on Freelander 2- 2.2Td4.
Equivalent to OEM 303-538.
EPB Brake Adaptor
DA6136
Adjustable 3 pin EPB brake adaptor with
standard 2 pin drive which is adjustable to
fit many modern vehicles. Kit also contains
a pneumatic brake caliper rewind tool -
⅜” D. This tool is for left and right hand
threaded pistons. Suitable for most 3/8” D
wind-back adaptors and pin type adaptors.
A great time saver in the workshop.
Crankshaft Pulley Holding Tool
DA6133
Provides the required components to
hold the crankshaft vibration damper in
place whilst undoing the very tight pulley
mounting bolt. Equivalent to OEM 303-191,
303-192, 303-193, 303-194. Designed to be
used with a ½” D Power Bar. For use on
AJ V8 3.2, 4.0, 4.2 & 4.4 petrol engines.
Other Workshop Tools
Propshaft Fastener Tools
> Size - 9/16” 6 point (hexagon)
> Total length - 150mm
> Outside diameter - 20mm
Specialist socket for propshaft fasteners on most
Land Rovers. The 9/16” socket end is a perfect hexagon
with rounded tip profiles to ensure the whole turning
power is transferred onto the flanks of the nuts instead
of on the corners. The socket’s slim wall construction
and wine glass profile, coupled to an integral slimline
extension means it fits perfectly between the UJ yokes
and over the propshaft nuts without fouling. The 9/16” AF
nuts are common to Series, Defenders (90 & 110 up to
latest vehicles), Discovery 1, Discovery 2, Range Rover
Classic and Range Rover P38.
DA1065 ⅜” square drive
DA1119 ½” square drive
Crankshaft Trigger Wheel Installer Tool
DA6550 NEW
Discovery 3
Discovery 4
Range Rover Sport - Mk1
Required to install the crankshaft position
sensor ring when fitted with TdV6 engine.
Specifically requested to repair sensor
wheel dropping off or cracking.
Equivalent to OEM 303-1130
Overall dimension: 125mm